↑ arvau

Wikipedia / Double-sideband suppressed-carrier transmission

Double-sideband suppressed-carrier transmission (DSB-SC) is transmission in which frequencies produced by amplitude modulation (AM) are symmetrically spaced above and below the carrier frequency and the carrier level is reduced to the lowest practical level, ideally being completely suppressed.

In DSB-SC, unlike simple AM, the wave carrier is not transmitted; thus, much of the power is distributed between the side bands, which implies an increase of arial coverage in DSB-SC, for the same power consumption.

DSB-SC transmission is a special case of Double-sideband reduced-carrier transmission. It is used for radio data systemss. Single sideband suppressed-carrier mode is frequently used in amateur radio voice communications, especially on high-frequency bands.

Efficiency and compatibility

DSB-SC is basically an amplitude modulation wave without the carrier, therefore reducing power waste, giving it a 50% efficiency. This is an increase compared to normal AM transmission (DSB) that has a maximum efficiency of 33.333%, since of the power is in the carrier which conveys no useful information and both sidebands containing identical copies of the same information. Single sideband suppressed-carrier (SSB-SC) is 100% efficient.

Despite its efficiency advantages, a standard AM receiver (such as an envelope detector) is unable to receive the signal properly, due to it missing the carrier which is key for these sets. A good compromise might be to use DSB with reduced carrier, making it able to be used with AM receivers while having a reasinably good efficiency.

Spectrum

The DSB-SC signal is similar to a standard AM transmission, with two sidebands, one above the carrier and one below the carrier frequency (upper and lower sidebands, respectively), only missing the large spike of the carrier frequency.

Spectrum plot of a DSB-SC signal:

Generation

DSB-SC is generated by a mixer. The signal produced is the product of the message signal and a carrier signal. The mathematical representation of this process is shown below, where the product-to-sum trigonometric identity is used.

Demodulation

In DSBSC, coherent demodulation is achieved by multiplying the DSB-SC signal with the carrier signal of the same phase as in the modulation process, analogous to the modulation process. This resultant signal is passed through a low pass filter to produce a scaled version of the original message signal:

, this second term is much higher in frequency than the original message. Once this signal passes through a low pass filter, the higher frequency component is removed, leaving just the original message.

Distortion and attenuation

For demodulation, the demodulation oscillator's frequency and phase must be exactly the same as the modulation oscillator's, otherwise, distortion and/or attenuation will occur.

To see this effect, take the following conditions:

The resultant signal can then be given by

represents a cyclic inversion of the recovered signal, which is a serious form of distortion.

Waveforms

Below is a message signal that one may wish to modulate onto a carrier, consisting of a couple of sinusoidal components with frequencies respectively 800 Hz and 1200 Hz.

.

The carrier, in this case, is a plain 5kHz) sinusoid—pictured below.

The modulation is performed by multiplication in the time domain, which yields a 5kHz carrier signal, whose amplitude varies in the same manner as the message signal.

The name "suppressed carrier" comes about because the carrier signal component is suppressed—it does not appear in the output signal. This is apparent when the spectrum of the output signal is viewed. In the picture shown below we see four peaks, the two peaks below 5,000 Hz are the lower sideband (LSB) and the two peaks above 5,000 Hz are the upper sideband (USB), but there is no peak at the 5,000 Hz mark, which is the frequency of the suppressed carrier.

Applications

DSB-SC is used to encode the difference signal in the FM broadcast stereo subcarrier. The (L+R) signal is limited from 0Hz to 15kHz. The (L−R) signal, which is also limited to 15kHz, is modulated onto a 38kHz DSB-SC carrier, occupying 23kHz to 53kHz. A 19kHz pilot signal, at exactly half the 38kHz sub-carrier frequency and with a precise phase relationship to it is also generated. The pilot is transmitted at reduced modulation level and used by the receiver to identify a stereo transmission and to regenerate the 38kHz sub-carrier with the correct phase. The composite stereo multiplex signal contains the main channel (L+R), the pilot tone, and the (L−R) difference signal. The (L-R) is added or subtracted with (L+R) to extract the left and right channels.

References