A quantum point contact (QPC) is a narrow constriction between two wide electrically conducting regions, of a width comparable to the electronic wavelength (nano- to micrometer)., the so-called conductance quantum.

Quantum point contacts were first reported in 1988 by a Dutch team from Delft University of Technology and Philips Research and, independently, by a British team from the Cavendish Laboratory. They are based on earlier work by the British group which showed how split gates could be used to convert a two-dimensional electron gas into one-dimension, first in silicon and then in gallium arsenide.

This quantisation is reminiscent of the quantisation of the Hall conductance, but is measured in the absence of a magnetic field. The zero-field conductance quantisation and the smooth transition to the quantum Hall effect on applying a magnetic field are essentially consequences of the equipartition of current among an integer number of propagating modes in the constriction.

Fabrication

There are several different ways of fabricating a quantum point contact. It can be realized in a break-junction by pulling apart a piece of conductor until it breaks. The breaking point forms the point contact. In a more controlled way, quantum point contacts are formed in a two-dimensional electron gas (2DEG), e.g. in GaAs/AlGaAs heterostructures. By applying a voltage to suitably shaped gate electrodes, the electron gas can be locally depleted and many different types of conducting regions can be created in the plane of the 2DEG, among them quantum dots and quantum point contacts. Another means of creating a QPC is by positioning the tip of a scanning tunneling microscope close to the surface of a conductor.

Properties

Geometrically, a quantum point contact is a constriction in the transverse direction which presents a resistance to the motion of electrons is the conductance of the contact. This formula resembles Ohm's law for macroscopic resistors. However, there is a fundamental difference here resulting from the small system size which requires a quantum mechanical analysis.

It is most common to study QPC in two dimensional electron gases. This way the geometric constriction of the point contact turns the conductance through the opening to a one dimensional system. Moreover, it requires a quantum mechanical description of the system that results in the quantisation of conductance. Quantum mechanically, the current through the point contact is equipartitioned among the 1D subands, or transverse modes, in the constriction.

It is important to state that the previous discussion does not take into account possible transitions among modes. The Landauer formula can actually be generalized to express this possible transitions , is the transition matrix which incorporates non-zero probabilities of transmission from mode n to m.

At low temperatures and voltages, unscattered and untrapped electrons contributing to the current have a certain energy/momentum/wavelength called Fermi energy/momentum/wavelength. Much like in a waveguide. The current carried by such a quantum state.

This is a fundamental result; the conductance does not take on arbitrary values but is quantized in multiples of the conductance quantum, which is expressed through the electron charge and the Planck constant is determined by the width of the point contact and roughly equals the width divided by half the electron wavelength.

On increasing the temperature, one finds experimentally that the plateaux acquire a finite slope until they are no longer resolved. This is a consequence of the thermal smearing of the Fermi-Dirac distribution (here ∆E is the subband splitting at the Fermi level). This is confirmed both by experiment and by numerical calculations.

An external magnetic field applied to the quantum point contact lifts the spin is independent of the width of the constriction, given by the theory of the quantum Hall effect.

The 0.7 anomaly

, the so-called 0.7-structure, arising due to enhanced electron-electron interactions arising from a smeared van Hove singularity in the local 1D density of states in the vicinity of the charge constriction. Unlike the conductance steps, the 0.7-structure becomes more pronounced at higher temperature. 0.7-structure analogues are sometimes observed on higher conductance steps. Quasi-bound states arising from impurities, charge traps, and reflections within the constriction may also result in conductance structure close to the 1D limit.

Applications

Apart from studying fundamentals of charge transport in mesoscopic conductors, quantum point contacts can be used as extremely sensitive charge detectors. Since the conductance through the contact strongly depends on the size of the constriction, any potential fluctuation (for instance, created by other electrons) in the vicinity will influence the current through the QPC. It is possible to detect single electrons with such a scheme. In view of quantum computation in solid-state systems, QPCs can be used as readout devices for the state of a quantum bit (qubit). In device physics, the configuration of QPCs is used for demonstrating a fully ballistic field-effect transistor. Another application of the device is its use as a switch. A nickel wire is brought close enough to a gold surface and then, by the use of a piezoelectric actuator, the distance between the wire and the surface can be changed and thus, the transport characteristics of the device change between electron tunneling and ballistic.

References

Further reading